AT&T Call Management System Instrukcja Użytkownika Strona 2
- Strona / 227
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
TO ORDER
COPIES
OF THIS
MANUAL
Call: AT&T Customer information Center on 800-432-6600
In Canada Call 800-255-1242
Write: AT&T Customer Information Center
2855 North Franklin Road
P.O. Box 19901
Indianapolis, Indiana 46219-1385
TO COMMENT ON THIS MANUAL
Call: The AT&T Document Development Organization
Hot Line: 800-334-0404
In North Carolina Call 919-727-3167
While reasonable efforts were made to ensure that the information
in this document was complete and accurate at the time of printing,
AT&T can assume no responsibility for any errors.
Changes or corrections to the information contained in this
document may be incorporated into future reissues.
Published by
The AT&T Documentation
Management Organization
Copyright© 1988 AT&T
All Rights Reserved
Printed in U.S.A.
- AT&T System 75 1
- And System 75XE 1
- TO ORDER 2
- OF THIS 2
- TO COMMENT ON THIS MANUAL 2
- Contents 3
- . . 9
- . . . . .208 10
- ● . ● 0. ● * 12
- INTRODUCTION 13
- ORGANIZATION 14
- UPGRADE PROCESS SYSTEM 75 15
- 2. Software Upgrade 18
- 555-200-500 20
- Updating 20
- Version 2 System Features 20
- 3. Prerequisite Hardware 21
- Figure 8 34
- (Component Side) 34
- Customer’s Translations 38
- Version 2 Translations 38
- VERSION 3 40
- Basic V2 to V3 Upgrade 41
- 1. Hardware Upgrades 41
- 2 (TN720/TN738), and 42
- 2. Software Upgrades 43
- 4. Service Interruption 46
- Circuit Pack 49
- Assign Version 3 53
- Translations 53
- Create Tape Backup 54
- Port Assignment Record 55
- UPGRADE PROCESS SYSTEM 56
- Out and Remove Hunt 61
- Groups To Be Rearranged 61
- Add or Replace Circuit 63
- Assign Version 3 Translations 65
- SUBSYSTEM UPGRADE 68
- PROCEDURE FOR UPGRADES 69
- SMALL CABINET CONTROL CARRIER 78
- Down System 79
- Replace Control Carrier 79
- PREREQUISITES 82
- ● 20 B25A Connector Cables 83
- PROCEDURE FOR UPGRADE 84
- Figure 13 86
- Figure 14 89
- Figure 15 91
- Pallet-Mounted System 75 91
- Figure 16 92
- Ramps Installed on Pallet 92
- CABINET (REAR VIEW) 95
- Figure 17 95
- Figure 22 102
- Power Up System 103
- Figure 23 104
- UPGRADE TRANSLATIONS 107
- Performed On-Site 109
- ADDITIONS 112
- Figure 24 113
- Figure 25 114
- Blank Circuit Pack Faceplate 114
- Figure 26 115
- Service Interruption 126
- Verify System Status 126
- Save Translations 126
- Power Down System 126
- Install Port Carrier 127
- Added Translations 129
- Update Port Assignment Record 129
- REAR VIEW 133
- Figure 32 134
- Bus Wiring Diagram 134
- Unpack and Inspect for Damage 137
- Figure 35 139
- Figure 36 140
- AC Power Requirements 140
- Position Port Cabinets 141
- Connect TDM Bus Cables 141
- DOOR LATCH 142
- Figure 37 142
- CABINET CLIP 143
- Figure 39 144
- TDM Bus Connections 144
- Install Ground Plate(s) 146
- Install Cabinet Clip(s) 148
- Install Cable Clamps 148
- Port Circuit Packs 148
- Install Cables 149
- Connect AC Power 149
- Enter Added Translations 150
- Figure 43 154
- Figure 44 155
- Ramps Installed 155
- Figure 45 156
- Auxiliary Cabinet 156
- 5. ADD ATTENDANT CONSOLE 157
- 6. ADD SELECTOR CONSOLE 158
- Figure 46. Selector 159
- CO, FX, WATS, AND PCOL TRUNKS 160
- 8. ADD DID TRUNKS 160
- 9. ADD TIE TRUNKS 161
- Table F 163
- DS1 TIE TRUNK SERVICE 164
- Add Circuit Packs 165
- SPEECH SYNTHESIS 167
- 12. ADD CODE CALLING ACCESS 167
- 13. ADD POOLED MODEM 168
- 14. ADD OFF-PREMISES AND 169
- OUT-OF-BUILDING TERMINALS 169
- 15. ADD EXTERNAL RINGING 170
- 18. ADD PagePac PAGING SYSTEM 172
- PagePac 20 173
- PagePac VS* 173
- PagePac 50/100/200 173
- 19. ADD MUSIC-ON-HOLD ACCESS 175
- 22. ADD INTEGRATED RECORDED 177
- ANNOUNCEMENT 177
- 23. ADD RECORDED TELEPHONE 178
- DICTATION ACCESS 178
- 24. ADD INADS INTERFACE 179
- 25. ADD APPLICATIONS 179
- INTERFACE (System 179
- PROCESSOR 179
- 75 Only) 179
- RECORDING INTERFACE 182
- EMERGENCY TRANSFER 184
- 28. ADD INFORMATION SYSTEM 185
- NETWORK INTERFACE 185
- INTERFACE 187
- (AUDIX) INTERFACE 190
- System Status 191
- 33. ADD PROPERTY MANAGEMENT 194
- SYSTEM (PMS) ACCESS 194
- TO REPLACE TWO 8-PORT ANALOG 195
- LINE CIRCUIT PACKS 195
- SYSTEM (DCS) INTERFACE 197
- System 75 198
- System 75 XE 198
- Make System Test Call 202
- Test Attendant Console 203
- Test Selector Console 204
- Test External Ringing 205
- Queue Warning Indicator 206
- Test Integrated Announcement 208
- Description 209
- Test Loudspeaker Paging 210
- Test Code Calling 210
- Test Music-on-Hold 211
- Emergency Transfer 212
- Test INADS Interface 213
- Test Tie Trunks 214
- Test DID Trunks 216
- Test CO Trunk 217
- Procedure—Incoming CO Trunk 218
- Interchange 219
- REFERENCES 220
- 75 and System 75 XE 224
Powiązane produkty i podręczniki dla Oprogramowanie AT&T Call Management System
(18 strony)
(6 strony)© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.070 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji