AT&T Telephone R1V2 Instrukcja Użytkownika

555-520-500Issue 1, June 1987AT&T SYSTEM 25ADMINISTRATIONMANUAL FOR R1V2

Maintaining system security. Notifying company management (and AT&T) about problems, alarms, and servicecomplaints.If you have questions about

Administering Tape Save/Restore OperationsIf you do not have a digital tape unit, you should skip this chapter.The procedures described below assume t

4 Press the REWIND button, and wait for the tape unit tocompletely rewind tape. [You should do this beforebeginning any save, verify, or restore opera

To troubleshootIf the save is successful, the SAT displays:SAVE COMPLETED SUCCESSFULLY5 Press the STOP/EJECT button on the tape unit.6 Rewind the tape

To troubleshoot5 Rewind the tape.6 Label the tape with the date and time. Store the tape in asafe place.If the verification is unsuccessful, the SAT d

To troubleshoot4 Type c.The line now reads:Save/Restore: Action = 3 Data = 1The tape unit automatically starts the Restore procedure atthis point an

System SearchesThis section describes how to search for various system information.Most searches require a minimum of two levels of search specificati

PDCs of Group Call 1 At Action = , enter 1.Coverage Sender Stations2 At Data = , enter 13 At Action = , enter 2.4 At Data = , enter the call

PDCs of Stations thatHunt to a SpecifiedStation1 At Action = , enter 1.2 At Data = , enter 5.3 At Action = , enter 2.4 At Data = , enter th

PDCs of Call Pickup1 At Action = , enter 1.Group Member Stations2 At Data = , enter 9.3 At Action = , enter 2.4 At Data = , enter the call p

Note This search expects input in the form NNN or in theform N•• where N is the initial digit or two digitsidentifying the station, trunk, special por

How to Use the SystemThis chapter describes the way you interact with the system using the System AdministrationTerminal (SAT). First, it tells you ho

Translated BoardLocations1 At Action = , enter 12 At Data = , enter 17.3 At Action = , enter 2.4 At Data = , enter information from tables 16

Port Location of External This search requires a PDC for input; it returns the portAlertlocation (CSSPP) of the external alert associated with thestat

DDCs that can dial for a 1 At Action = , enter 1.station or data port viaThird-Party Call Set-Up2 At Data = , enter 22.3 At Action = 2, enter

Display Support SearchesThe Display Support feature lets you search for IDs (or names) associated with PDCs, DDCs,FPDCs, DGC groups, and trunk numbers

Display ID for a Trunk1 At Action = , enter 1.LDN (trunks only)2 At Data = , enter 41.3 At Action = 2, enter the trunk LDN.Number for a given1 A

Listing Circuit PacksThis item lets you list the board type, vintage, and cabinet location for each circuit pack insystem, except the CPU and Memory C

Administering RS232 ParametersAction/data pairs associated with Main Menu item 10 (RS232) are used to administerSystem 25 peripheral equipment: System

1 At Action = , enter 1.Reassign an RS232connector function2At Data = , enter the function you want to assign to theTarget connector from the follo

Command ReferenceLIST OF TABLESTABLE 16-1 PORT/PDC Administration, Voice Terminal (Menu=1/2)TABLE 16-2 Voice Terminal Type CodesTABLE 16-3 Feature But

Command ReferenceThe tables in this chapter are intended to help those thoroughly familiar with systemadministration locate specific information witho

You can also end an administration session by: Unplugging the cable from the modular jack connecting the terminal to the system. Disconnecting the R

TABLE 16-1 PORT/PDC Administration, Voice Terminals (Menu=1/2)ACTIONDESCRIPTIONDATA0Physical port numberCSSPP1Enter terminal type code[See Table 16-2

TABLE 16-2 Voice Terminal Type CodesIf the Terminal Type is:Code:Single-line without message waiting indicator201Single-line with message waiting indi

TABLE 16-3 Feature Button Translation (Menu=1/2)“Action=100” is required before action(s) 101-104 listed in this table are administered.ACTIONNOTESBU

TABLE 16-3 10 Feature Button Translation (Menu=1/2) (continued)“Action=100” is required before action(s) 101-104 listed in this table are administered

TABLE 16-4 Multiline Set Button Defaults7 - SYS ACCESS†12 - FLEX DSS 17 - FLEX DSS 29 - FLEX DSS8 - SYS ACCESS† 13 - ACCT ENTRY 18 - FLEX DSS30 - FLE

TABLE 16-6 Direct Trunk Attendant Console Button Defaults (Cold-Start Defaults)7 - SYS ACCESS†12 - FLEX DSS17 - Trunk 000129 - Trunk 00098 - SYS ACCES

TABLE 16-7 Direct Trunk Attendant Console Defaults (Administration-Installed Defaults)7 - SYS ACCESS†8 - SYS ACCESS†9 - REP DIAL10 - REP DIAL11 - LAST

TABLE 16-9 PORT/PDC Administration, Data Terminals (Menu=1/2)ACTION DESCRIPTIONDATA0Physical port numberCSSPP1Enter data type code[See Table 16-10]2E

TABLE 16-9 PORT/PDC Administration, Data Terminals (Menu=1/2) (continued)ACTIONDESCRIPTIONDATA70Allow keyboard dialing/Command Mode*[1=Y / 0=N]71Allow

TABLE 16-10 Data Port Type CodesIF THE DATA PORT TYPE ISData Line Card (DLC)functionality for ZTN126 orTN726STARLAN Interface CircuitPack (STARLAN CP

The System 25 Administration Main MenuWhen you log in to the administration terminal, you see the Main Menu. This menu allowsyou to enter one of sever

TABLE 16-11 Port Administration, Trunks (Menu=1)ACTIONDESCRIPTIONDATA0 Physical port numberCSSPP1 Enter trunk port type code [See Table 16-12]2Enter

TABLE 16-12 Trunk Type CodesIf the Trunk Type is:Ground Start, COGround Start, WATS, FXLoop Start, COLoop Start, WATS, FXPBX/CentrexDID Immediate Dial

TABLE 16-13 TrunkTRUNK CLASS-OF-SERVICE(FOR ALL TRUNKS EXCEPT DID)COSNIGHTOUTWARDINSHORTCODESERVICE SIGNALINGONLYDISCONNECT0TT1TT●2TT●3TT●●4DP5DP●6DP

TABLE 16-14 Port Administration, Auxiliary Equipment (Menu=1)ACTIONDESCRIPTIONDATA0Display physical port number, in the form CSSPP1Enter special feat

TABLE 16-15 Special Feature Port Type CodesThis table shows data values associated with Action = 1 on Table 16-14TN742,FEATUREZTN78TN763 ZTN76ZTN77TN7

TABLE 16-16 Port OptionsPORTS, Station/Trunk/Special Port Circuit Board OptionsFOR QUALIFIED SYSTEMS TECHNICIANS ONLY*(See Table 16-17, “Applicable O

TABLE 16-17 Applicable OptionsSee WARNING for Table 16-16. Also note that a bullet in a box on this tableindicates that the default value for that act

TABLE 16-18 PDC Administration (Menu=2)ACTIONDESCRIPTIONDATA0Move this station to a new port[CSSPP (new port assignment)](moved-to port must be vacan

TABLE 16-19 System Administration (Menu=4)ACTIONDESCRIPTION3456711-182526252627303132333440Assign the number of rings beforeunanswered calls extended

TABLE 16-19 System Administration (Menu=4) (continued)ACTIONDESCRIPTIONDATA41Specify the number of rings before calls[0-31; 2]are sent to call cover

Selecting a Main Menu ItemTo select an item from the Main Menu, just type the number of the item you want followedby (Return)If you type (Return) by i

TABLE 16-19 System Administration (Menu=4) (continued)ACTIONDESCRIPTIONDATA82Switched Loop Attendant system: Queue[group number (1-32),should act as

TABLE 16-20 Standard Call Type DefaultsFOR SWITCHED LOOP SYSTEMS ONLYDEFAULTDEFAULTCALL TYPECODEPRIORITYATTENDANTDial Attendant (0)140Call Following -

TABLE 16-22 Floating PDC Administration (Menu=5)ACTIONDESCRIPTION DATA1List active FPDCs2Add an FPDC [FPDC to be added]3Delete an FPDC [FPDC to be de

TABLE 16-24 Toll Calls Allowed (TCA) List Administration (Menu=7)ACTION DESCRIPTIONDATA1List numbers in a TCA list2 Add a number to the list[NXX or N

TABLE 16-25 Searches: Action Items (Menu=8)ACTIONDESCRIPTIONDATA1Search for PDCs of call coverage senders12Call coverage receiver group[1-32 or 101-1

TABLE 16-25 Searches: Action Items (Menu=8) (continued)ACTIONDESCRIPTIONDATA1 Search for physical port locations162Port or board type (see Tables 16

TABLE 16-26 Board Type—Wildcard RepresentationCATEGORY:BOARD DESCRIPTION:DATA:EmptyEmpty Slot (Searches 15 & 17 only)0StationSingle-line Voice Ter

TABLE 16-27 Port/Board Type—Specific RepresentationCATEGORY:Voice StationTrunkDESCRIPTION:Single-line without message waitingSingle-line with message

TABLE 16-27 Port/Board Type—Specific Representation (continued)CATEGORY:DESCRIPTION: DATA:SpecialFirst Service Circuit1101External Alerts253First Pa

TABLE 16-28 Save/Restore and System Restarts (Menu=9)ACTIONDESCRIPTIONDATA1 Save (Backup) translations[1 to run]2 Verify translations[1 to run]3 Rest

Command FunctionsThe previous section introduced you to the basic command formats. This section shows youhow to enter or change: an action number, dat

TABLE 16-30 Automatic Route Selection Administration (Menu=11)ACTION DESCRIPTIONDATA100Assign a pattern number[1-8]101Assign a start time for subpatt

TABLE 16-30 Automatic Route Selection Administration (Menu=11) (continued)ACTIONDESCRIPTIONDATA401Assign the ARS access code[dial code: 9]402Assign

Requirements for the SATThis section defines requirements for the system administration terminal (SAT). Any dataterminal with an RS-232C interface tha

IndexAAccess code, speed dialing, 4-10Access Toll Calls Allowed list, 4-7Account Code Entry feature, 10-9Account Codes, 4-5Action groups, 2-7 – 2-8Act

DData, 2-4Data button, 10-8search, 14-2Data Line and STARLAN CP Ports,administration, 8-1Data port, 2-6Data stations, 3-5administration, 8-1Data termi

NNight Service, 5-5, 7-6, 7-10search, 14-4Night Service button, 10-10Night Service trunk, 2-9Number of DID digits, 4-6OOn-line switch, 17-1One-button

Terminals, 3-5Tie trunks, 5-6Time of Day, 4-4Toll Calls Allowed Lists, 2-9, 4-7 - 4-8forms, 3-4Toll restriction class, 7-5, 7-8data stations, 8-5Toll

Here is an example of the D command:You see:Port = 10604 Action = 7 Data = 0>To change, you enter D 5 (Return) and see:> Data = 5Port = 10604 A

Here is an example of the T (target select) command with PDC (Main Menu item 2):You see:PDC = 9876 Action = 1 Data = 201>You enter T 8765 (Return

You enter 6789 (Return) and see:> Data = 6789Port = 10408 Action = 2 Data = 6789>There are no more members in this action group, so the syste

You enter C and see:FPDC: Action = 1 Data = 7777>You enter C and see:FPDC: Action = 1 Data = 8888>You enter C and see:FPDC: Action = 1 Data =

©1987 AT&TAll Rights ReservedPrinted in USATO ORDER COPIES OF THIS DOCUMENT REFER TO DOCUMENT NUMBER 555-520-500.Contact: Your AT&T sales repr

System ResponsesDuring an administration session, there are occasions when you may enter inappropriateinformation at a prompt.While System 25 does not

Print MessagesThis kind of message is straightforward–it conveys information. A print message does notdescribe an error condition.A print message appe

Initializing the SystemThis section outlines the procedure for administering initial system translations (that is, forinitializing) the system).To ini

TABLE 3-1 Default Dial Code AssignmentsPortDefault CodeTrunk Numbers (not part of dial plan)0001-0104Station Dial Codes:Multiline voice terminals 200

Initialization SequenceBegin with a Cold StartWhen you administer the initial translations, it is important that you begin from a knowncondition. You

TABLE 3-2 Initialization SequenceFrom the information providedon this form,Enter these translations:1 System Options FormEnter system toll restriction

TABLE 3-2 Initialization Sequence (continued)8 Voice and Data Station RecordsAssign all station ports (except for attendant consoles),formfollowing th

Administering System-Wide OptionsThis section describes how to set system-wide options which include: Toll Restrictions Call Coverage Pooled Mod

To allow toll restricted 1 At Action = , enter 31.stations to make toll calls2 At Data = , enter 1 for yes or 0 for no. The default is 1.withi

To specify the number ofrings before calls are sentto call coverage or callfollowing calls return totheir home station1 At Action = , enter 41.2 At

FCC WARNING STATEMENTFederal Communications Commission (FCC) Rules require that you be notified of thefollowing: This equipment generates, uses, and

To state whether there is 1 At Action = , enter 64.disconnect on received2 At Data = , enter 1 for yes or 0 for nospaceThe default is [email protected]

Call Accounting OptionsFrom the Main menu prompt, enter 4, then set the followingcall accounting options:SMDRSpecify whether SMDR1 At Action = , ent

Miscellaneous System OptionsFrom the Main menu prompt, enter 4, then set the followingsystem options:To blockmaintenance 1 At Action = , enter 70.b

Administration PasswordTo change the1 From the Main menu prompt, enter 4.administration password2 At Action = , enter 75.3 At Data = , enter the

To delete a code from the1 At Action = , enter 3.list2 At Data = , enter the code you want to delete exactly as itwas listed using Action=1.Floati

Virtual FacilitiesA Virtual Facility (VF) is a call-routing facility which is not defined by the physical facility(trunk) over which calls are routed.

System Speed DialingSystem Speed Dialing allows you to enter a four-character code at any terminal to call theassociated phone number.Keep the followi

Administering TrunksThis section shows you how to: Assign and remove trunks Assign class-of-service parameters for various types of trunksAssigning

TABLE 5-1 Trunk-Type CodesIf the Trunk Type is:You Enter:Ground Start, CO701*Ground Start, WATS, FX702Loop Start, CO 801*Loop Start, WATS, FX802PBX/Ce

Removing a TrunkTo remove a trunk1 From the Main menu prompt, enter 1.2 At Port = , enter the physical port you want to remove inthe form CSSPP.3 A

System 25 DocumentsThe following System 25 product documents are available for your reference. Copies may bepurchased from the Customer Information Ce

TABLE 5-2 Trunk Class of Service (for all trunks except DID)COSNIGHTOUTWARDINCODESERVICE SIGNALING ONLY0TT1 TT●2TT3TT●●4DP5DP●6DP7DP●8●TT9●TT●10●TT11●

Class-of-Service OptionsFollow the procedures below to assign class-of-service options to this trunk.Pooled Facility Access1 At Action = , enter 4.

1 At2 At Action = , enter 7.Data = , enter:1 to select Directed Night Service0 to select TAAS Night Service.The default is 1.Delay Announcement:

Assigning Trunk Options to a SLAC SystemThe following options apply only to systems using the Switched Loop Attendant Console(SLAC), and are not admin

Administering Auxiliary EquipmentThis section discusses how to assign and remove AT&T System 25 auxiliary equipmentassociated with special ports.

Paging (Associated with Auxiliary Trunk Port)You can assign Paging to up to three zones.Each paging zone must be assigned to aseparate port. Follow th

Paging (Associated with CO Trunk Port)If the paging system is connected to a loop or ground start trunk port, simply assign a trunkfacility access cod

You see Action = 2. At Data = , enter: 0 - if you do not want Music on Special Hold 1 - if you want Music on Special HoldPooled ModemTo assign

Administering Voice Stations Assign voice terminals Remove voice terminals Assign and change station dial codes Assign class of serviceUsing the

TABLE 7-1 Voice Terminal Type CodesTerminal Type:Code:Single-line without message waiting indicator201Single-line with message waiting indicator2025-B

Contents1234IntroductionImplementation Planning FormsThe System Administrator’s RoleUsing this ManualHow to Use the SystemLogging In to System 25Corre

45At Data = , enter 0.If this station is associated with another station(s) forfeatures such as Call Coverage, Automatic Intercom, etc.,you will see

Moving a Voice StationUse this procedure when you want to move a station – its features, button assignments, andPDC — to another port. Keep these cons

To restrict dial access to1 At Action = , enter 4.all other trunk pools2 At Data = , enter 1 for yes or 0 for no. The default is 0.To restric

Station Hunting: To1 Atadminister this station tohunt to another station if2 AtbusyorAction = , enter 12.Data = , enter the PDC of the station to

To assign a trunk to this1 At Action = , enter 52.station for Night Service2 At Data = , enter a four-digit trunk number.Note Any given trunk can h

To assign a toll restriction1 At Action = , enter 14.class2 At Data = , enter a toll class number, 0-4, from thefollowing list (the default is 0):0

Group Call Coverage:specify which receivergroup will cover thisstation’s callsTo1 At2 At Action = , enter 7. ‡Data = , entera call coverage gr

Night Service: To display1 At Action = , enter 51.the number of any trunksassigned to this station2 To continue the list, enter C after each trunk

Administering Data Line and STARLAN CP PortsProcedures in this section apply to: A data terminal connected to a Data Line Card (DLC) via an ADU, but

4 At Data = , enter the code for the data terminal you’readding: 1801 for a DLC (ZTN126 or TN726) 1802 for a STARLAN CP (ZTN84).Note The only way

5Administering Trunks67Assigning a TrunkRemoving a TrunkAssigning Class of Service to DID TrunksAssigning Class of Service to AllOther TrunksAdministe

NO MORE BLOCKSc for continue, any other key for abort5 Enter c.You see the following display when the station isremoved:Action = 1 Data = 0Note If y

To move a data station to1 From the Main Menu prompt, enter 2.a new port2 At PDC = , enter the DDC of the station you want tomove.3 At Action = ,

To restrict access to all1 At Action = , enter 4.other trunk pools2 At Data = , enter 1 for yes or 0 for no. The default is 0.To set calls to

To assign ARS Facility1 At Action = , enter 15.Restriction Level (FRL)2 At Data = , enter the FRL number, 0-3, from the followinglist (the default

Set Baud Rate and ParityNote For each data terminal, indicate all permissible operatingspeeds and any required parity.To auto-adjust baud rate1 At Ac

Can this terminal operate1 At Action = , enter 66. ‡at a baud rate of 4800bps?2 At Data = , enter 1 for yes or 0 for no. The default is 0.

To allow the user to1 At Action = , enter 71. ‡configure data port2 At Data = , enter 1 for yes or 0 for no. The default isparameters1. For a

Administering Attendant EquipmentSystem 25 can have two attendant consoles, either Switched Loop Attendant Consoles(SLACs) or Direct Trunk Attendant C

Direct Extension Selector (DXS) Console System 25 assigns by default a selector (DXS)console, associated with the first attendant console, to the sec

Move an Attendant ConsoleTo move an attendant1 From the Main menu prompt, enter 2.console to a different port(DTAC or SLAC)2 At PDC = , enter the PD

9101112Administering Attendant EquipmentAssign a Switched Loop Attendant ConsoleAssign a Second Attendant ConsoleMove an Attendant ConsoleChange an At

To remove an attendant 1 From the Main Menu prompt, enter 1.console2 At Port = , enter the CSSPP for the attendant consoleyou’re removing.3 At Acti

5 Type t and at Port = , enter the new CSSPP for the DXSconsole.6 At Action = , enter 1.7 At Data = , enter 1601 for the first DXS console 160

Assign Attendant Options (DTAC and SLAC)To assign options to anFrom the Main menu prompt, enter 4.attendant consoleAssign options to the DTAC or SLAC

To assign the number of1 At Action = , enter 7.rings before unansweredDGC calls are sent to the2 At Data = , enter the number of rings, 1-31.delay

To assign a DID access1 At Action = , enter 84.code to the SLAC2 At Data = , enter the DID access code people outside thesystem will use to call t

SLAC Call-Type OptionsCall-type options let you set priorities for the eight types of calls that come into the attendantconsole queue.By default, the

Assigning Message-Center-Like DefaultsTo specify which1 At Action = , enter 90.attendant console shouldhave message-center-like2 At Data = , ente

To specify which1 At Action = , enter 91.attendant should receiveeach call type (dual-SLAC2 At Data = , enter the call-type code, 1-8 (see Table 9-

Administering Button AssignmentsThis section describes how to assign buttons to: Multiline sets Attendant consoles Selector consolesNote Some bu

Selector Console (DXS)The selector console (DXS) has seven group select buttons that can be assigned, or“programmed.”(It also has a non-programmable t

1314151617Administering Tape Save/RestoreOperationsUsing the Digital Tape UnitSave Your TranslationsVerify the Saved TranslationsRestore the System Tr

Button Assignment TablesTABLE 10-1 Multi line Set Button Defaults7 - SYS ACCESS†12 - FLEX DSS17 - FLEX DSS29 - FLEX DSS8 - SYS ACCESS† 13 - ACCT ENTRY

TABLE 10-3 Direct Trunk Attendant Console (Cold Start Defaults)7 - SYS ACCESS†12 - FLEX DSS17 - Trunk 0001 29 - Trunk 00098 - SYS ACCESS†13 - ACCT ENT

TABLE 10-5 DXS Console Button Defaults2.. 3.. 4.. 5.. 6..7.. 8..TEST†TABLE 10-6 MET Set Button Defaults7 - SYS ACCESS†8 - SYS ACCESS†9 - REP D

Assigning Buttons to Multiline Terminals and AttendantConsolesTo assign a feature to abutton on a multilinevoice terminal orattendant console, beginwi

5 You see the prompt, Action = 103.6 Is this station the “owner” of this line?At Data = , enter 1 for yes or 0 for no.7 You see the prompt, Actio

To assign Automatic 1 At Action = , enter 101.Intercom (AUTO ICOM)[AG] (This is a two-2 At Data = , enter 8.station feature. ) 3 You see the pro

To assign Call Coverage-1 At Action = , enter 101.Individual (COVER-IND)[AG]2 At Data = , enter 12. †3 You see the prompt, Action = 102.4 At Da

To assign an AUTO ANS1 At Action = , enter 101.button2 At Data = , enter 21.To assign Last Number1 At Action = , enter 101.Dialed (LAST # DIA

To assign Position BusyNote For a DTAC, this feature can only be administered when(POS BUSY)there are two attendant consoles. For a SLAC, this feature

Administering Direct Group Calling (DGC) GroupsThis section tells you how to add DGC groups, assign access codes to DGC groups, and addand remove DGC

IntroductionThis manual provides the information you need to administer AT&T System 25 station,network access, and system features. This includes

To disable DGC queuing1 At Action = , enter 2.2 At Data = , enter 1 for yes or 0 for no. The default is 0.To list stations in a DGC1 At Action

Administering Automatic Route Selection (ARS)The procedures in this section show you how to define ARS patterns and lists. If you do notdefine these p

ARS PatternsThe next set of procedures tells you how to assign routing patterns for “A” and “B”subpatterns. Each subpattern consists of a set of route

To assign a stop time for1 At Action = , enter 102. †subpattern A2 At Data = , enter the stop time in the form HOUR,MINUTES (HHMM).To assign Route

To allow Subpattern A to1 At Action = , enter 140. †overflow to DDD2 At Data = , enter 1 for yes or 0 for no, The default is0,To assign an FRL

To assign an FRL for1 At Action = , enter 221. †Subpattern B, Route 2:2 At Data = , enter an FRL, 0-3.To assign Route 3 for1 At Action = , enter

Area Code Routing TableAll North American area codes are assigned to routing pattern 1 by default, except area codesN00 and N10, which default to 0.To

Add Central Office Code1 At Action = , enter 512. ‡to this HAC exceptionlist.2 At Data = , enter a three-digit Central Office Code (NXX).Remove Cen

Other Area Codes Exception ListEnter a Pattern Number1 At Action = , enter 800.to handle this Other AreaCodes Exception2 At Data = , enter a patter

Assign “associated”1 At Action = , enter 701. ‡Area Code.2 At Data = , enter the associated area code.How many leading digits1 At Action = , ente